RVMethod

RV Tire Age: Read the DOT Date Code and Know When to Get an Inspection

Find the tire manufacture date, check wear and damage, and decide when to ask a tire professional about replacement.

Published by Yousha · RV Method · 3 min read

Research-based educational guidance. Model-specific procedures and professional review are not claimed. How these guides are prepared · Report a correction

Before you begin: Use your RV and component manuals for model-specific procedures. Stop and use a qualified professional for electrical, propane, structural, or other work beyond your training.

How to read the tire manufacture dateThe illustrative last four digits 2423 mean the tire was made in week 24 of 2023. The first two digits are the week and the last two are the year. Look on both tire sidewalls because the full date code may appear on only one side.Example DOT date code2423Week 24Year 2023
Illustration only, based on NHTSA's explanation of the four-digit tire date code. This is not a photo of an RV tire or a replacement-age rule.
Close-up of a tire sidewall showing DOT marking and the final four date digits 0312
Real tire example: the final four digits, 0312, indicate week 03 of 2012. This is a car tire photo; the date-code reading principle also applies to RV tires. Compare both sidewalls of your own tire. Photo: Richard Huber / Wikimedia Commons · CC BY-SA 4.0 · unmodified.

Find the full date code

Look for the DOT Tire Identification Number on a tire sidewall. The last four digits identify the week and year of manufacture: for example, 2423 means week 24 of 2023. The full date code may appear on only one sidewall, so check both sides without reaching under an unsupported RV.

Record the code for every tire, including the spare if fitted. If the code is hidden or unreadable, ask a tire professional to inspect it safely. The manufacture date is not the installation date.

Why age matters even when tread looks good

RV tires can age while the vehicle is parked and the tread still looks usable. NHTSA specifically flags recreational vehicles and other low-mileage vehicles because aging may be overlooked. Heat, sunlight, storage, inflation, and load all matter.

The DOT code gives a manufacture date, not a universal expiration date. NHTSA says some vehicle and tire makers recommend replacement at six to ten years regardless of treadwear. Goodyear’s RV-tire bulletin, for example, recommends replacement after six years in service for its tires and explains how to use the DOT date when the service-start date is unknown. That is Goodyear guidance, not a rule for every tire. Follow your RV and tire makers’ instructions and ask a tire professional when history is uncertain.

Inspect pressure, tread, and damage

Check all tires, including the spare, with an accurate gauge at least monthly and before a long trip. NHTSA describes a cold tire as one not driven for at least three hours. Use the vehicle placard and applicable tire/load guidance; the sidewall maximum alone is not the recommended operating pressure. For a loaded motorhome or trailer with uncertain axle loads, have the RV weighed and obtain the correct tire-maker inflation information.

Look for cuts, cracks, bulges, uneven wear, embedded objects, and repeated air loss. A tire can be unsafe before it reaches an age threshold. Do not drive on a tire with a bulge, exposed cords, serious damage, or unexplained pressure loss; consult a tire professional.

Keep a tire record you can act on

Write down the date code, tire brand and model, size and load rating, position on the RV, installation date if known, pressure specification, inspection date, and any service recommendation. Keep a clear photograph of each code if you can take one safely.

Compare the record with tire manufacturer guidance, your RV manual, and any applicable recall. Before a long trip, resolve damage or age questions with a qualified tire shop rather than assuming a visual check is enough.

What this guide does not decide

It cannot set a replacement date for your exact tires without their make, model, use, storage, and inspection history. It also does not replace a tire professional’s assessment of load rating, wheel condition, or damage. Use the linked NHTSA resource to understand the date code and basic checks, then follow the applicable manufacturer guidance.

Documented example: a date code and a damaged sidewall

This is a documentation-based scenario, not a record of work performed on a particular RV.

Manual or source: NHTSA TireWise: aging, date codes, and damage checks

  1. Suppose a tire has a full DOT code ending in 0320 and visible sidewall cracks. NHTSA’s date-code rule reads that ending as the third week of 2020; it does not tell us when the tire was installed.
  2. Record the tire position, make, model, size, pressure specification, and damage in a dated photo. Check the spare and the other road tires as well. Do not rely on remaining tread to dismiss age or cracking.
  3. NHTSA says damage can require replacement before any age threshold. Ask a tire professional to assess this tire before travel and compare the tire and RV makers’ replacement guidance. Do not treat the illustrative code alone as an automatic pass or fail.
  4. Save the professional recommendation and any replacement receipt with the tire record. The next check should use the correct cold-pressure guidance for the installed tire and actual RV load.

Manufacturer manuals & further reading

Use these official resources to find details for your equipment. Match the brand, model, and revision; another RV’s procedure may not apply to yours.

Keep a record: Record your tire checks →